Maxent model for BRPE

This page contains some analysis of the Maxent model for BRPE, created Wed May 14 13:32:43 PDT 2014 using Maxent version 3.3.3k. If you would like to do further analyses, the raw data used here is linked to at the end of this page.

Analysis of omission/commission

The following picture shows the omission rate and predicted area as a function of the cumulative threshold. The omission rate is is calculated both on the training presence records, and (if test data are used) on the test records. The omission rate should be close to the predicted omission, because of the definition of the cumulative threshold.

The next picture is the receiver operating characteristic (ROC) curve for the same data. Note that the specificity is defined using predicted area, rather than true commission (see the paper by Phillips, Anderson and Schapire cited on the help page for discussion of what this means). This implies that the maximum achievable AUC is less than 1. If test data is drawn from the Maxent distribution itself, then the maximum possible test AUC would be 0.974 rather than 1; in practice the test AUC may exceed this bound.

Some common thresholds and corresponding omission rates are as follows. If test data are available, binomial probabilities are calculated exactly if the number of test samples is at most 25, otherwise using a normal approximation to the binomial. These are 1-sided p-values for the null hypothesis that test points are predicted no better than by a random prediction with the same fractional predicted area. The "Balance" threshold minimizes 6 * training omission rate + .04 * cumulative threshold + 1.6 * fractional predicted area.

Cumulative threshold	Logistic threshold	Description	Fractional predicted area	Training omission rate
1.000	0.010	Fixed cumulative value 1	0.193	0.000
5.000	0.050	Fixed cumulative value 5	0.101	0.000
10.000	0.106	Fixed cumulative value 10	0.065	0.031
7.528	0.078	Minimum training presence	0.080	0.000
18.772	0.216	10 percentile training presence	0.037	0.094
10.593	0.113	Equal training sensitivity and specificity	0.062	0.062
7.528	0.078	Maximum training sensitivity plus specificity	0.080	0.000
2.279	0.023	Balance training omission, predicted area and threshold value	0.146	0.000
11.591	0.127	Equate entropy of thresholded and original distributions	0.058	0.094

Pictures of the model

This is a representation of the Maxent model for BRPE. Warmer colors show areas with better predicted conditions. White dots show the presence locations used for training, while violet dots show test locations. Click on the image for a full-size version.

Click here to interactively explore this prediction using the Explain tool. If clicking from your browser does not succeed in starting the tool, try running the script in C:\Final\maxentoutputs\BRPE_explain.bat directly. This tool requires the environmental grids to be small enough that they all fit in memory.

Analysis of variable contributions

The following table gives estimates of relative contributions of the environmental variables to the Maxent model. To determine the first estimate, in each iteration of the training algorithm, the increase in regularized gain is added to the contribution of the corresponding variable, or subtracted from it if the change to the absolute value of lambda is negative. For the second estimate, for each environmental variable in turn, the values of that variable on training presence and background data are randomly permuted. The model is reevaluated on the permuted data, and the resulting drop in training AUC is shown in the table, normalized to percentages. As with the variable jackknife, variable contributions should be interpreted with caution when the predictor variables are correlated.

Variable	Percent contribution	Permutation importance
mintemp	36.4	70.9
maxtemp	32.9	27.4
percipitation	30.8	1.7
averagetemp	0	0

The following picture shows the results of the jackknife test of variable importance. The environmental variable with highest gain when used in isolation is mintemp, which therefore appears to have the most useful information by itself. The environmental variable that decreases the gain the most when it is omitted is mintemp, which therefore appears to have the most information that isn't present in the other variables.

Raw data outputs and control parameters

The data used in the above analysis is contained in the next links. Please see the Help button for more information on these.
The model applied to the training environmental layers
The coefficients of the model
The omission and predicted area for varying cumulative and raw thresholds
The prediction strength at the training and (optionally) test presence sites
Results for all species modeled in the same Maxent run, with summary statistics and (optionally) jackknife results

Regularized training gain is 2.849, training AUC is 0.986, unregularized training gain is 3.381.
Algorithm converged after 260 iterations (7 seconds).

The follow settings were used during the run:
32 presence records used for training.
10018 points used to determine the Maxent distribution (background points and presence points).
Environmental layers used (all continuous): averagetemp maxtemp mintemp percipitation
Regularization values: linear/quadratic/product: 0.244, categorical: 0.250, threshold: 1.680, hinge: 0.500
Feature types used: linear quadratic hinge
jackknife: true
outputdirectory: C:/Final/maxentoutputs/
samplesfile: C:/Final/samples/maxent.csv
environmentallayers: C:/Final/layers/
autorun: true
Command line used: -e C:/Final/layers/ -s C:/Final/samples/maxent.csv -o C:/Final/maxentoutputs/ outputformat=Logistic outputfiletype=asc -J -a

Command line to repeat this species model: java density.MaxEnt nowarnings noprefixes -E "" -E BRPE jackknife outputdirectory=C:/Final/maxentoutputs/ samplesfile=C:/Final/samples/maxent.csv environmentallayers=C:/Final/layers/ autorun